Robinson Willey SuperEco Desire Wartungshandbuch

The data plate is located at the bottom left hand side of the fireboxThis handbook contains both Installer and user information and must be left with

6.2.3 For the ‘Manual’ version, remove the burner tray by removing the two screws.Refer to Fig 11b.6.2.2 Remove the fender mask by removing the two sc

6.3 METHOD OF INSTALLATIONThere are two methods for securing the fire to the wall which are:(a) Fixing by tension cable.(b) Screwing the fire directly

6.4 GAS CONNECTIONNOTE: The appliance must be connected to gas with rigid or semi-rigid tubing, from either the right or left hand side, or by conceal

137.0 COMMISSIONING7.1 INSTALL FUEL EFFECT COMPONENTSThe base ceramic matrix, side cheeks and fuel effect components are illustrated in Fig 2. The fir

Fig 20.50 mmSMOKE MATCH IN TUBE7.3 TEST FOR SPILLAGEA test for spillage must be made before the installed fire is left with the user. This is carried

15IMPORTANT NOTES1. Turn off the gas supply to the fire before starting any servicing.2. Always test for gas soundness after servicing or exchanging a

169.4 PILOT ASSEMBLYThe pilot is an atmosphere sensing device and must be replaced as a complete unit. Repair must not be undertaken.NOTE: If the fire

17The following are possible fault conditions. Check the items mentioned and repair or replace parts as necessary. The list is not exhaustive but a fa

USER SECTION11.1 SHELF HEIGHT AND SIDE CLEARANCESThe fire may be fitted beneath a shelf. COMBUSTIBLE SHELFA shelf may be fitted above the heater prov

19All cleaning should be carried out when the fire is cold.Generally the fire will only need dusting. Any painted surface or metal part should be clea

INTRODUCTION AND GENERAL REQUIREMENTSTECHNICAL DATACONTENTS OF SCREW PACKCONTENTS OF CERAMIC FUEL COMPONENT PACKCONDITIONS OF INSTALLATIONSITING GENE

2013.1 MANUAL CONTROL VERSION (NOT DESIRE)LIGHT THE FIREThe control knob has the markings OFF, PILOT, HIGH and LOW.The control knob is located behi

The Fuel Effect pack contents are illustrated in Figs 2a & 2b. The fire is supplied with the rear brick effect panel already fitted.Unpack the Fue

22Position pebbles (B) and (E), then locate (C) centrally on the bed.Locate pebble (M) and (N) at the sides, supported between (J) & (O) and (L) &

Fig 26bFig 27bFig 28bFig 29b2314.3 COAL LAYOUTPosition the four separately packed coals in the corresponding indentations on the front edge of the bas

14.4 LIGHTING WITH A TAPERAPPLY TAPER HERE2415.1 PARTS REPLACEABLE BY USER15.0 SPARES AND SERVICETHE GAS CONSUMERS' COUNCIL (GCC) IS AN INDEPENDE

1.1 DIMENSIONS((Overall) mmHeight 595Width 500Depth 140Forward Projection 90 (Desire 65)Height to top of flue aperture 5041.2 INPUTS AND PRESSURESNatu

3.0 CONTENTS OF SCREW PACKACDEFGIBFig. 1.JH4.0 CONTENTS OF CERAMIC FUEL COMPONENT PACKThe contents of the ‘pebble’ set are as follows(see fig 2a) : -

5.1 SITING GENERALThis fire is suitable for hearth mounting only on a non-combustible hearth at least 13mm thick and measuring at least 630mm wide by

5.2.2 PRE-CAST FLUE OF MINIMUM SIZE (Fig. 4)This fire can be installed into a properly constructed pre-cast flue conforming to B.S. 1289 : 1975 or B.S

Fig 5.Fig 6.Fig 7.660.0560.5500.0244.046.5100.0==GAS SUPPLY PIPE KNOCK OUTS78.04 SPIGOT SCREWS750mm MINIMUM (2in)5.2.3 REBATED SURROUND INSTALLATIONWh

5.2.4 METAL FLUE BOX/125mm DIAMETER FLUES (Figs. 8 and 9)This fire may be installed in a double walled or insulated metal box built to the requirem

96.0 INSTALLATION OF FIREFig 10.6.1 UNPACKINGThe fire is packed with the rear brick board already fitted in position. When unpacking refer to the chec